Last Modified: 11-29-2007 1.6 A
Service Category: Vehicle Exterior Section: Window/Glass
Model Year: 2008 Model: Sequoia Doc ID: RM000003GSY000X
Title: WINDOW / GLASS: POWER WINDOW REGULATOR MOTOR: REMOVAL (2008 Sequoia)

REMOVAL

HINT:

  • Use the same procedure for both the RH and LH sides.
  • The procedure described below is for the RH side.

1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION (2008 Sequoia) .

2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH DOOR / HATCH: FRONT DOOR: DISASSEMBLY (2008 Sequoia)+

3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG DOOR / HATCH: FRONT DOOR: DISASSEMBLY (2008 Sequoia)+

4. REMOVE FRONT ARMREST BASE UPPER PANEL DOOR / HATCH: FRONT DOOR: DISASSEMBLY (2008 Sequoia)+

5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY DOOR / HATCH: FRONT DOOR: DISASSEMBLY (2008 Sequoia)+

6. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY

HINT:

Use the same procedure as for the LH side MIRROR (EXT): OUTER REAR VIEW MIRROR: REMOVAL (2008 Sequoia)+ .

7. REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

HINT:

Use the same procedure as for the LH side EXTERIOR PANELS / TRIM: FRONT DOOR BELT MOULDING: REMOVAL (2008 Sequoia)+ .

8. REMOVE NO. 1 FRONT DOOR TRIM BRACKET DOOR / HATCH: FRONT DOOR: DISASSEMBLY (2008 Sequoia)+

9. REMOVE FRONT DOOR SERVICE HOLE COVER DOOR / HATCH: FRONT DOOR: DISASSEMBLY (2008 Sequoia)+

10. REMOVE FRONT DOOR GLASS RUN DOOR / HATCH: FRONT DOOR: DISASSEMBLY (2008 Sequoia)+

11. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY DOOR / HATCH: FRONT DOOR: DISASSEMBLY (2008 Sequoia)+

12. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY DOOR / HATCH: FRONT DOOR: DISASSEMBLY (2008 Sequoia)+

13. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY

(a) Using "TORX" socket wrench T25, remove the 3 screws and the power window regulator motor.

14. REMOVE REAR DOOR FRAME GARNISH DOOR / HATCH: REAR DOOR: DISASSEMBLY (2008 Sequoia)+

15. REMOVE REAR DOOR ARMREST BASE UPPER PANEL DOOR / HATCH: REAR DOOR: DISASSEMBLY (2008 Sequoia)+

16. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG DOOR / HATCH: REAR DOOR: DISASSEMBLY (2008 Sequoia)+

17. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY DOOR / HATCH: REAR DOOR: DISASSEMBLY (2008 Sequoia)+

18. REMOVE REAR DOOR TRIM NO. 2 BRACKET DOOR / HATCH: REAR DOOR: DISASSEMBLY (2008 Sequoia)+

19. REMOVE REAR DOOR SERVICE HOLE COVER DOOR / HATCH: REAR DOOR: DISASSEMBLY (2008 Sequoia)+

20. REMOVE REAR DOOR WINDOW FRAME REAR MOULDING

HINT:

Use the same procedure as for the LH side EXTERIOR PANELS / TRIM: REAR DOOR WINDOW FRAME MOULDING: REMOVAL (2008 Sequoia)+ .

21. REMOVE REAR DOOR GLASS OUTER WEATHERSTRIP

HINT:

Use the same procedure as for the LH side EXTERIOR PANELS / TRIM: REAR DOOR BELT MOULDING: REMOVAL (2008 Sequoia)+ .

22. REMOVE REAR DOOR GLASS RUN DOOR / HATCH: REAR DOOR: DISASSEMBLY (2008 Sequoia)+

23. REMOVE REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY DOOR / HATCH: REAR DOOR: DISASSEMBLY (2008 Sequoia)+

24. REMOVE REAR DOOR WINDOW FRONT GUIDE SUB-ASSEMBLY DOOR / HATCH: REAR DOOR: DISASSEMBLY (2008 Sequoia)+

25. REMOVE REAR DOOR GLASS SUB-ASSEMBLY DOOR / HATCH: REAR DOOR: DISASSEMBLY (2008 Sequoia)+

26. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY DOOR / HATCH: REAR DOOR: DISASSEMBLY (2008 Sequoia)+

27. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY

(a) Using "TORX" socket wrench T25, remove the 3 screws and the power window regulator motor.